Servocret RS

Repair Filler and Patching Compound

  • One-component, shrinkage-compensated, self-curing formulation
  • Designed for layers up to 2" (50 mm)
  • Suitable for interior, exterior, and submerged applications
  • Enables fast-track repair of concrete floors and walls
  • Ready for ceramic tile installation in just 1 hour
  • Offers exceptional sag resistance for vertical and horizontal use
  • Delivers high compressive and flexural strength
  • Ideal as a base layer beneath tile or self-leveling underlayment

Servocret RS is a rapid-setting, cement-based compound enhanced with acrylic polymers, engineered for high-performance patching, leveling, and modeling repairs beneath ceramic tile coverings. It features excellent sag resistance, making it ideal for vertical and horizontal applications in interior, exterior, and submerged environments, including swimming pools.

Typical Applications:

  • Filling holes, trenches, step edges and small voids
  • Repairing concrete foundations, pedestals, patios, and balconies
  • Smoothing and leveling plaster, brick, and concrete surfaces

Once fully cured, Servocret RS provides a durable, load-bearing surface suitable for pedestrian and vehicular traffic, and is fully compatible with Kiesel tile adhesives and self-leveling systems.

All substrates must be solid, dry, clean, and free from dust, oil, grease, or any other contaminants that could affect adhesion.

For highly absorbent surfaces, proceed as follows:

  1. Prime using one of the following:
    a. Okatmos® UG 30
    b. Okatmos® DSG (diluted 1:10 with water)
    c. Okatmos® EG 20
  2. Allow the primer to dry completely.
  3. Apply a contact scratch coat and immediately proceed with the filling application.

Proper priming improves substrate sealing and ensures strong, lasting adhesion of Servocret RS.

  1. Mixing: Combine one 25 kg bag of Servocret RS with approximately 3.5 liters (0.93 US gallons) of clean, cool water. Use a mixer at a maximum speed of 600 RPM to create a smooth, lump-free consistency.
  2. Application: Apply the material with a trowel or spatula, adjusting as needed.
  3. Smoothing/Modeling: Finish the surface using a moist sponge and wooden board for a refined, level result.
  4. Pumping (Optional): Compatible with auger-type pumping systems (e.g., Putzmeister, Innotec) for efficient large-scale application.
  5. Protection: Immediately protect fresh surfaces from direct sunlight, drafts, and elevated temperatures using plastic sheeting.

Color

Grey

VOC

0,0 g/L

Application

Interior, exterior, wet areas, (e.g. pools)

Antimicrobial technology

Yes

Thickness

1/8“- 2“ (2 - 50 mm)

Application temperature

41 °F to 77 °F (+5 °C to +25 °C) (substrate)

Water demand

Approx. 0.93 U.S. gals./25 kg bag (approx. 3.5 l/25 kg powder)

Processing time*

Approx. 30 minutes

Ready for traffic* / ready for installation*

After approx. 60 minutes

Fully loadable*

After approx. 24 hours

GISCODE

ZP 1 - low in chrome acc. to TRGS 613

Storage

Approx. 6 months (Climate-controlled, unopened packaging)

* 

At 68 °F (+20 °C) and 65 % relative humidity. Higher temperature and low humidity decrease, lower temperature and high humidity increase this value respectively.

Thickness (inches)Thickness (mm)Coverage (ft² per 25 kg bag)Coverage (m² per 25 kg bag)
1/8"3.2 mm565.2
1/4"6.3 mm282.6
1/2"12.7 mm141.3
1"25.4 mm70.7

Clean all tools with water immediately after use.

DescriptionItem No. 
42 x 25 kg/ 55 lbs paper bags110264015705110264

The aforementioned information, especially the proposals for processing and utilizing our product, is based on our knowledge and experience. We recommend that you carry out your own tests in every case to ensure the suitability of our products for the intended process and processing purposes because of the different materials and the working conditions which lie beyond our area of influence. No liability can be derived from this advice or from verbal advice, unless we are responsible for (criminal) intent or gross negligence in this respect.