Okatmos® UG 30
Acrylic polymer based universal primer and bonding agent
- For absorbent and non-absorbent substrates
- Will bond to a variety of existing substrates
- Quick drying
- Solvent-free and low emission
- Application of primer eliminates odor, microbiological interactions, prevents mold, and promotes proper bonding
- Provides high bond strength
- For interior and exterior* applications
- Breathe easy technology
Solvent-free, acrylic based primer with aggregates providing excellent bonding characteristics. Okatmos® UG 30 will bond and adhere to absorbent and non-absorbent substrates before interior levelling work or tile and natural stone installations. Okatmos® UG 30 can also be applied over properly prepared cut-back adhesive, old or badly sanded asphalt floors, terrazzo, tile, particle board, chipboard, OSB, cement backer units, and concrete screeds and well bonded ceramic tiles.
*When used over existing exterior tiles a waterproofing membrane Servoflex DMS 1K Plus SuperTec is required. Metal and similar substrates must be rust-free and cleaned with Acetone. Odorless and environmentally friendly. As part of the Okatmos®-product-line, Okatmos® UG 30 avoids the development of odors and stenches originating in microbial interactions in the floor-structure. It is therefore very suitable for renovation purposes.
The substrate must be dry, clean and load-bearing ready. Remove all dry and loose particles and bitumen cut-back mechanically. Follow additional guidelines located in TTMAC and TCNA manuals.
Shake container before use.
Apply Okatmos® UG 30 undiluted onto substrate with lamb skin roller, brush or similar. Dilute Okatmos® UG 30 for porous concrete, untreated floors and other absorbent gypsum based substrates 1:1 with water. Do not begin leveling or installation before primer has completely dried.
Color
Blue
Application
Interior, exterior walls and floors
n/a
0.0 g/L
Yes
Application temperature
41 °F to 86 °F (+ 5 °C to + 30 °C) (substrate)
Substate dependable: approx. 10 minutes (over cementitious substrate). Wooden structure might require longer drying time - minimum 12 hours.
Suitable
D 1 acc. to TRGS 610
EMICODE®
EC 1Plus (GEV)
EC 1Plus (GEV)
Store in frost protected area for up to 15 months (keep from freezing)
*
At 68 °F (+ 20 °C) and 65% relative humidity. Higher temperature and low humidity decreases, lower temperature and high humidity increase this value respectively.
| Application | Coverage (g/m² per 1 L) | Substrate/Condition | 1 US quart (square feet) | 2.20 US gallons (sq ft) |
|---|---|---|---|---|
| Binder (undiluted) | 150 | On non-absorbent, textured substrates (plywood, OSB, similar) | 86 | 721 |
| Binder (diluted 1:1) | 75 | On cementitious, mineral, or gypsum-based substrates | 161 | 1,432 |
| Bonding agent (undiluted) | 120 | On clean ceramic or stone tiles in good condition | 86–97 | 829–893 |
Coverage may vary based on substrate texture, porosity, and application technique.
Brush, lamb skin roller.
Clean tools with water immediately after application.
| Description | Item No. | |
|---|---|---|
| 60 x 2.49 U.S. gals./ 10 kg plastic canister | 80035 | |
| 50 boxes with 12 x 1.0 qts (1 kg) plastic bottles | 80068 |
The aforementioned information, especially the proposals for processing and utilizing our product, is based on our knowledge and experience. We recommend that you carry out your own tests in every case to ensure the suitability of our products for the intended process and processing purposes because of the different materials and the working conditions which lie beyond our area of influence. No liability can be derived from this advice or from verbal advice, unless we are responsible for (criminal) intent or gross negligence in this respect.